Converting gas engine to hydrogen - Miller Welding Discussion …
网页2008年8月15日 · 08-24-2008, 12:23 PM. Originally posted by projectwelder View Post. Internal combustion engines work by compressing air fuel mixture, hydrogen is very hard to compress so compression ratios would need to be lowered. Alot of auto engines have been converted to run on methane or propane, but hydrogen would be tough.
Bobcat propane conversion - Miller Welding Discussion Forums
网页2007年1月27日 · Bobcat propane conversion. 01-27-2007, 09:39 AM. I'm considering putting a conversion kit on my bobcat. There's two main reasons I'm looking at this. One, I really don't put a lot of hours/year on it, so there's always that fight with varnish and gasoline stabilizers. Two, if I ever need it for long term power, I can tie it into the tank for ...
Calibrating argon/CO2 mixer - Miller Welding Discussion Forums
网页2010年6月21日 · The Smith Argon/Oxygen mixer is set up differently than the Argon/CO2 mixer. Here the range is from 100%-84% Argon (the rest being Oxygen). The larger gradations make it possible to adjust for a 95/5, 98/2, or 99/1 mix for spray arc transfer with Argon/O2. (little hotter arc than that achieved using CO2).
Miller 225 g carb - Miller Welding Discussion Forums
网页2011年4月29日 · Tweet. #1. Miller 225 g carb. 04-29-2011, 10:32 AM. I have a miller 225 plus with an onan p216 engine. I have to run it with the choke out approximatly 75%. Without the choke pulled it will run high speed but rough and will die when it drops to idle speed. I removed carburetor and soaked in cleaner and reassembled it and ran two tanks with sea ...
Legend with Onan Performer 18XSI, Inter no-start, fuel pump full …
网页2012年1月25日 · I have a Legend gas powered welder with the Onan Performer 18XSI engine. On cooler mornings when I go to start it, it wont start. I inspected th fuel pump and on the back side of the diaphram where the vaccum …
Lincoln Classic III Carburetor - Miller Welding Discussion Forums
网页Tweet. #1. Lincoln Classic III Carburetor. 03-27-2013, 12:34 PM. I have a Classic 3 with the Continental TM27 gas engine and it needs carb work. It has old gas in it and it only runs with the choke on.
wounded Bobcat! - Miller Welding Discussion Forums
网页wounded Bobcat! 04-04-2017, 06:39 PM. Hey guys, so my Bobcat 250g with Kohler engine is running real rough! I have replaced fuel pump, filter, solenoid, and module. Only 700 hrs on it, but it's filthy, it didn't run when I got it. So I tore apart the carb and cleaned it, replaced the gaskets. Also new plugs, oil, and battery.
AC vs. DC - Miller Welding Discussion Forums
网页2009年2月12日 · Welcome to the forum! Maybe we can simplify your curiosity. Any machine that plugs into a conventional or 3-phase receptical operates on AC current. The machines have transformers, converters, inverters, rectifiers to "convert" this into "DC." The only "pure" DC machine(s) are the Lincoln Classic 200 & 300 engine drives. (I won't confuse you ...
Miller 250NT wont idle - Miller Welding Discussion Forums
网页Miller 250NT wont idle. 02-09-2024, 07:55 AM. Good Morning, I have a miller 250 NT with the Kohler engine Spec# 64712 and Welder Serial LE262634. I have tested the PC1 board and it checks out based on the troubleshooting steps found on this forum the old solenoid would not move on the bench. I have installed a Kohler 2443506S solenoid which ...
Blown F5 fuse on Trailblazer 325 - Miller Welding Discussion Forums
网页2019年3月3日 · Blown F5 fuse on Trailblazer 325. 03-03-2019, 07:44 PM. I’m currently troubleshooting a Trailblazer 325 with the Kolher Gas engine S/N MH040162R. Engine will only run at idle. During start up the F5 fuse will blow. Owner was using welder as a generator during a power outage for a couple days when it suddenly dropped to idle and now blows the ...