Cisco 7600 Series Routers
网页2009年7月2日 · The Cisco 7600 Series is the industry's first carrier-class edge router to offer integrated, high-density Ethernet switching, carrier-class IP/MPLS routing, and 10-Gbps interfaces, benefiting enterprises and helping enable service providers to deliver both consumer and business services over a single converged Carrier Ethernet network.
7600 Cheat Sheet - Cisco Community
网页7600 Cheat Sheet. 07-03-2009 02:39 AM - edited 03-01-2019 04:23 PM. Hank Nussbacher, Nussbacher Consulting, Kfar Saba, Israel. When converting from a 7200/7500 platform to a 7600 platform, there are many new commands that are specific to the 7600 platform. It is often confusing to remember all of them, so I have created a "7600 Cheat sheet":
C7600 replacement - Cisco Community
网页2016年1月12日 · C7600 replacement. Iulian Vaideanu. Level 4. Options. 01-12-2016 10:52 AM - edited 03-05-2019 03:06 AM. We have a couple of 7606-S / RSP720 core routers, each populated with one X6724-SFP and three X6708 cards, and we're looking to replace them with something else, mainly due to the oversubscription limits of the X6708s being …
Solved: 7600 stuck in RoMMon - Cisco Community
网页2011年4月28日 · Solved: I have a 7600 with ws-sup750 and when it boots it displays these errors: Cisco IOS Software, s72033_sp Software (s72033_sp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXH2a, RELEASE SOFTWARE (fc2) Technical Support:
Cisco 7600 high CPU due to interrupts
网页2014年1月14日 · router 1 communicates with router2 via router Cisco 7600. Normaly all traffic through Cisco 7600 is hardware switched. This Cisco 7600 has sup720 3BXL (IOS 12.2 (33)SRE6) and has MPLS PE functionality. Recently I noticed huge increase in CPU utilisation due to interrupts. CPU usage is 50% (only interrupt part).
Cisco 7600 portchannel load-balancing issue
网页2012年10月24日 · 9 Centralized Forwarding Card WS-F6700-CFC 3.1 Ok. So, I trying to configure the portchannels with different load-balancing mode: src-ip for port-channel 3 and dst-ip for port-channel 4. port-channel per-module load-balance. port-channel load-balance dst-ip. port-channel load-balance src-ip module 7.
Solved: Using L2TP xconnect on 7600/ES20 - Cisco Community
网页2010年8月11日 · Would just add snip from doc: "On the Cisco 7600 series routers, L2TPv3 is a line card feature that was traditionally implemented only on the 7600-SIP-400 line card. In Cisco IOS Release 12.2(33)SRD, L2TPv3 is supported on the 7600-ES+20/40 line cards in the hardware, with the same capabilities (excluding the non-Ethernet interface support) …
xconnect within the router (Cisco7600) - Cisco Community
网页Level 1. Options. 07-28-2011 03:03 PM. actually, on a 7600 line card, if you want to xconnect from one port to another you can. Use the xconnect with port number. If you are looking to bring in traffic on one port and send out multiple ports on same card do it this way/. int gig0/1. service instance 100 ethernet.
Known Issues on Cisco 7600 Router ES+ Line Cards
网页2012年3月6日 · Introduction ES+ linecards on Cisco 7600 Series Routers are using highly programmable components. Some of the issues observed on these cards had a symptom that would normally be interpretted as a hardware faiure, e.g. double-bit or repeated single-bit parity errors. Purpose Of This Document This d...
How to configure logging in Cisco IOS
网页2022年12月11日 · Use the logging source-interface configuration command to specify a particular IP address for syslog messages: Router (config)#logging source-interface Loopback0. E) Clearing the Router's Log. Use the clear logging command to clear the router's internal log buffer: Router#clear logging. Clear logging buffer [confirm]<enter>.