Frequently Asked Questions: Cisco Unified Border Element (CUBE)
2011年8月18日 · A: Cisco CUBE is an Integrated application with Cisco IOS software. CUBE functionality is supported in Cisco 2600XM, 2691, Cisco ISR 2800, 3800 series, Cisco VXR 7200, Cisco XR 12000, AS5400XM Universal gateways and the Service Provider Gateways.
Solved: How many calls handle by CUBE gateway - Cisco Community
2017年6月14日 · CUBE is a paper-based honor license (no file to install) that allows you to run the CUBE RTU (Right-to-Use) feature set after you have the UCK9 license installed. So ideally if you are continually exceeding 25 then you should buy more licences, but the exact capability again falls to hardware capability as of now.
Q4: What Platforms are supported for CUBE? A: Cisco CUBE is an Integrated application with Cisco IOS software. CUBE functionality is supported in Cisco 2600XM, 2691, Cisco ISR 2800, 3800 series, Cisco VXR 7200, Cisco XR 12000, AS5400XM Universal gateways and the Service Provider Gateways. Q5: Do we need Digital signal processors (DSPs) for CUBE?
Difference between Cisco SBC and CUBE
2015年7月8日 · Part of the Cisco ® Collaboration Edge Architecture, Cisco Unified Border Element (CUBE) version 12 is an enterprise-class Session Border Controller (SBC) solution that makes it possible to connect and interwork large, midsize, and small business unified communications networks with public and private IP communication services.
How to check active calls on CUBE Router? - Cisco Community
2023年1月18日 · This article explains Cisco CUBE commands to check number of active calls, call details and call count. Effective from Cisco IOS XE Amsterdam 17.2.1r, CUBE status display is enabled without configuring mode border-element license capacity sessions command. Licensed-Capacity and blocked call information is excluded from output.
CUBE Enforced Licensing - Cisco Community
2020年4月21日 · Hi, At the moment we don't have any installations using CUBE Smart Licensing, they all use the older trust based licensing where there's basically no enforcement at all. However a few installs are on ISR4xxx routers and I understand that at some point following an IOS upgrade these will move to Sma...
Solved: CUBE Show command for Dial Peers - Cisco Community
2017年2月14日 · Is there a Show command that will tell me what dial peer an active call is using? I have a 3945 with T1-PRIs and also a SIP trunk to the ITSP (CUBE). Connection to CUCM is with a SIP trunk, IOS is 15.4.3-M6a "Show Voice Call Status" shows the PRI calls, but not the CUBE calls. I don't want to run a ...
Solved: Adding SIP trunk to ISP on CUBE - Cisco Community
2024年1月26日 · The following Cisco live presentation will give you a better idea about the SIP Trunk configuration with the service provider. Deploying SIP Trunks with Cisco Unified Border Element . I have taken a few key bits from that and posting here. 1. Information required from Provider: 2. Enabling the CUBE application on your router/gateway: 3.
Call Admission Control (CAC) implementation on CUBE - Cisco …
2011年8月30日 · IP call capacity on CUBE works in conjunction with the Cisco Gatekeeper (GK) Call counting mechanism does not take into account the codec type used – this is taken into account by enabling bandwidth management on the Cisco GK; This only works if at least 1 call leg on CUBE is using H.323 . 3. CAC Based on Max Connections per destination
CUBE - SIP Options Keep Alive & Global Outbound Proxy - Cisco …
2019年3月17日 · Dear forum users. Below is one of my VoIP dial-peer in my CUBE to my CUCM cluster:- dial-peer voice 17702 voip description removed for confidentially preference 2 destination-pattern removed for confidentially progress_ind setup enable 3 session protocol sipv2 session target ipv4:10.100.12...